Cross Stitch Framing Tutorial.

Here’s a quick cross stitch framing tutorial for you all!

Before I start with this no doubt subpar tutorial, let me preface it with the fact that I am in no way precious about the way in which I finish a project. There are definitely neater ways to do it, so if you’re a perfectionist this mightn’t be for you! I also took the photos during the grim winter months here in the North East of England. To quote Florence & the Machine “no light, no light…”

Having said that, on the rare occasion I go all out with a frame this is the method that works for me, so here it is:

Things you’ll need:

  • Your ironed cross stitch with at least two inches of excess material around all edges of the design.
  • A photo frame
  • Acid-free foam board (sometimes labelled as foam core mount board). Make sure you get a colour that coordinates with your fabric, white for white etc.
  • Pins
  • Needle and strong thread (the thread in the photo was as weak as my tutorial game, so make sure you’ve got something strong enough to pull taut without snapping. I actually ended up using Anchor embroidery floss, which wasn’t ideal but just about did the job.)
  • Scissors (pictured are my tiny embroidery scissors, but you’d be better off using a pair of sharp habedashery scissors for trimming your cross stitch and kitchen scissors or something similar for the mount board) It’s even better to use a proper cutter for the board, but alas! I don’t have one.

IMG_1660

STEP ONE:

First off you need to cut your foam board down to a suitable size for the inside of your frame. My frame was 6 x 4 inches, so I cut it to a few millimetres shy of that. You’ll want it to fit inside the frame but still have a little bit of wiggle room at the edges  for when the cross stitch fabric is eventually folded around it. Check you’ve got that gap by trying the foam board in the frame, it shouldn’t be too snug or be wedged in there.

IMG_1664

STEP TWO:

Now that you have your expertly measured foam board at the ready, it’s time to pick up that lovely cross stitch of yours. Position it over the foam board, making sure that the design is central and level, and begin by folding the top side down.  Find the middle of your design and push a pin into the foam centre of the board right on the top edge. Repeat at the bottom.

IMG_1665

STEP THREE:

Repeat Step Two, this time at the centre of the left and right sides.  As you do this try to make sure that the fabric is as flat as it can be, and pulled fairly evenly across the board.

IMG_1667

STEP FOUR:

Start working your way out from the centre, placing pins diagonally opposite each other, a couple at a time on each side.  As you do this check that your design is still central, and that the fabric is laying flat and taut. Continue all the way round.

IMG_1689

STEP FIVE:

Now that you’ve finished pinning flip the whole thing over. This is where my shambolic tutorial skills once again show themselves. For reasons unknown I’m holding the whole thing the wrong way round in the photo below. S0 what looks like top to bottom is actually side to side. * Sighs*

IMG_1690

What you need to do is fold your sides inwards, and lace them together. I found doing the sides first is best for a flatter overall finish. For the lacing you’re going to need a really long length of your thread, as you can see I underestimated and had to do a shoddy retying job in the middle. For my lacing I started at about 1cm from the edge (you can go in closer to the edge than that if you want), and stitched backwards and forwards between the two sides. Pull it tight as you go, but make sure you’re not warping the board.

STEP SIX:

If you’re still with me here then not only are you some kind of modern hero, but the end is also in sight!

At this stage fold over the top and bottom edges and lace those too.

IMG_1692

As you can see my back isn’t the tidiest, but I left far more than two inches of excess around the piece and didn’t pull very tight with my stitches, so it’s all a bit bulkier than usual.

There are neater ways to finish a piece (there’s a snazzy method of folding your corners down and sewing them, which gives the whole thing a lovely finish), which I’d be happy to point you in the direction of if you’ d like to try them!

After you’ve done all of that you should find that the surface of your cross stitch is pulled nice and taut across the board, and that the edges are smooth.

STEP SEVEN:

Rejoice and remove those pins!

IMG_1693

STEP EIGHT:

Because you left that little bit of wiggle room at the start you should find that your cross stitch fits into the frame nice and snugly now.

IMG_1696

Finito!

This is just one of many ways to finish a cross stitch piece. There’s also the option of embroidery hoops (which I might do a tutorial for if  I ever recover from this one) and professional framing. Ultimately it’s all about personal preference and budget! If you have any questions, or spot any glaring mistakes then feel free to get in touch!

Thanks for reading,

Lauren x

*The Hold Fast pattern design is available over at the shop.

 

 

Advertisements

2 thoughts on “Cross Stitch Framing Tutorial.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s